Electro-Thermal Modeling of Power IGBT Module Cooled by A Heat Pipe Cooling System

Authors

  • Améni Driss Laboratoire Matériaux, Mesures et Applications (MMA), Institut National des Sciences Appliquées et de Technologie (INSAT), University of Carthage, Centre Urbain Nord, BP N° 676 – 1080 Tunis Cédex, Tunisia
  • Samah Maalej Laboratoire Matériaux, Mesures et Applications (MMA), Institut National des Sciences Appliquées et de Technologie (INSAT), University of Carthage, Centre Urbain Nord, BP N° 676 – 1080 Tunis Cédex, Tunisia
  • Mohamed Chaker Zaghdoudi Laboratoire Matériaux, Mesures et Applications (MMA), Institut National des Sciences Appliquées et de Technologie (INSAT), University of Carthage, Centre Urbain Nord, BP N° 676 – 1080 Tunis Cédex, Tunisia

DOI:

https://doi.org/10.37934/arfmts.86.1.105122

Keywords:

Electronics cooling, Heat pipes, IGBT, Electro-thermal modeling

Abstract

This paper deals with the development of an electro-thermal model of an Insulated Gate Bipolar Transistor (IGBT) with a water-cooled heat pipe cooling system. Firstly, a thermal model of the heat pipe cooling system is proposed. Then, an electro-thermal model of the IGBT is developed to predict the junction temperature variations in transient operation. The thermal model of the IGBT is determined on the base of the thermal-capacitance lumped method. The electrical model of the IGBT is developed by considering the effect of the junction temperature on its static electrical parameters. Finally, the electro-thermal model is considered in a boost converter application. The model predictions show the effectiveness of the heat pipe cooling system for different commutation frequencies. It is proved that the heat pipe cooling system can keep the junction temperature of the IGBT at values allowing safe operation.

Author Biographies

Améni Driss, Laboratoire Matériaux, Mesures et Applications (MMA), Institut National des Sciences Appliquées et de Technologie (INSAT), University of Carthage, Centre Urbain Nord, BP N° 676 – 1080 Tunis Cédex, Tunisia

ameni_driss@yahoo.fr

Samah Maalej, Laboratoire Matériaux, Mesures et Applications (MMA), Institut National des Sciences Appliquées et de Technologie (INSAT), University of Carthage, Centre Urbain Nord, BP N° 676 – 1080 Tunis Cédex, Tunisia

samah.maalej@insat.rnu.tn

Mohamed Chaker Zaghdoudi, Laboratoire Matériaux, Mesures et Applications (MMA), Institut National des Sciences Appliquées et de Technologie (INSAT), University of Carthage, Centre Urbain Nord, BP N° 676 – 1080 Tunis Cédex, Tunisia

chaker.zaghdoudi@insat.rnu.tn

References

Fikri, Bintang, Nandy Putra, Adi Winarta, Nasruddin A. Abdullah, and Bambang Ariantara. "Experimental investigation of modified direct evaporative cooler using heat pipe." Journal of Advanced Research in Fluid Mechanics and Thermal Sciences 55, no. 2 (2019): 209-217.

Abdullahi, Bala, Ahmed Elsayed, Raya Al-Dadah, Sa'ad Mahmoud, Abdel Fateh Mahrous, Nura Mu'az Muhammad, and Saidu Bello Abbakar. "Experimental and numerical investigation of thermosyphon heat pipe performance at various inclination angles." Journal of Advanced Research in Fluid Mechanics and Thermal Sciences 44, no. 1 (2018): 85-98.

Baheta, Aklilu Tesfamichael, Ahmed N. Oumer, and Sintayehu M. Hailegiorgis. "Analysing the thermal performance of heat pipe using copper nanofluids." Journal of Advanced Research in Fluid Mechanics and Thermal Sciences 45, no. 1 (2018): 149-155.

Rogers, Susan A. "Annual Progress Report for the Advanced Power Electronics and Electric Machinery Program." 2007 Annual Progress Report, Vehicle Technologies Program, US DOE (2007).

Bazzo, João Paulo, Tiago Lukasievicz, Marcio Vogt, Valmir de Oliveira, Hypolito José Kalinowski, and Jean Carlos Cardozo da Silva. "Thermal characteristics analysis of an IGBT using a fiber Bragg grating." Optics and Lasers in Engineering 50, no. 2 (2012): 99-103. https://doi.org/10.1016/j.optlaseng.2011.08.009

Avenas, Yvan, and Laurent Dupont. "Evaluation of IGBT thermo-sensitive electrical parameters under different dissipation conditions–Comparison with infrared measurements." Microelectronics Reliability 52, no. 11 (2012): 2617-2626. https://doi.org/10.1016/j.microrel.2012.03.032

Avenas, Yvan, Laurent Dupont, and Zoubir Khatir. "Temperature measurement of power semiconductor devices by thermo-sensitive electrical parameters—A review." IEEE transactions on power electronics 27, no. 6 (2011): 3081-3092. https://doi.org/10.1109/TPEL.2011.2178433

Lee, Tien-Yu. "Design optimization of an integrated liquid-cooled IGBT power module using CFD technique." IEEE Transactions on Components and Packaging Technologies 23, no. 1 (2000): 55-60. https://doi.org/10.1109/6144.833042

Hefner, Allen R. "A dynamic electro-thermal model for the IGBT." IEEE Transactions on Industry Applications 30, no. 2 (1994): 394-405. https://doi.org/10.1109/28.287517

Hsu, J-T., and Khai DT Ngo. "Behavioral modeling of the IGBT using the Hammerstein configuration." IEEE transactions on Power Electronics 11, no. 6 (1996): 746-754. https://doi.org/10.1109/63.542037

Ammous, Anis, Sami Ghedira, Bruno Allard, Hervé Morel, and Denise Renault. "Choosing a thermal model for electrothermal simulation of power semiconductor devices." IEEE Transactions on Power Electronics 14, no. 2 (1999): 300-307. https://doi.org/10.1109/63.750183

Ammous, Anis, Kaiçar Ammous, Hervé Morel, Bruno Allard, Dominique Bergogne, Fayçal Sellami, and Jean Pierre Chante. "Electrothermal modeling of IGBTs: Application to short-circuit conditions." IEEE Transactions on Power Electronics 15, no. 4 (2000): 778-790. https://doi.org/10.1109/63.849049

Luo, Zhaohui, Hyungkeun Ahn, and M. A. E. Nokali. "A thermal model for insulated gate bipolar transistor module." IEEE Transactions on Power Electronics 19, no. 4 (2004): 902-907. https://doi.org/10.1109/TPEL.2004.830089

Kojima, Takashi, Yuji Nishibe, Yasushi Yamada, Takashi Ueta, Kaoru Torii, Shoichi Sasaki, and Kimimori Hamada. "Novel electro-thermal coupling simulation technique for dynamic analysis of HV (hybrid vehicle) inverter." In 2006 37th IEEE Power Electronics Specialists Conference, pp. 1-5. IEEE, 2006.

Ciappa, Mauro, Wolfgang Fichtner, T. Kojima, Y. Yamada, and Y. Nishibe. "Extraction of accurate thermal compact models for fast electro-thermal simulation of IGBT modules in hybrid electric vehicles." Microelectronics Reliability 45, no. 9-11 (2005): 1694-1699. https://doi.org/10.1016/j.microrel.2005.07.083

Du, Bin, Jerry L. Hudgins, Enrico Santi, Angus T. Bryant, Patrick R. Palmer, and Homer Alan Mantooth. "Transient electrothermal simulation of power semiconductor devices." IEEE Transactions on power electronics 25, no. 1 (2009): 237-248. https://doi.org/10.1109/TPEL.2009.2029105

Hefner Jr, Allen R., and David L. Blackburn. "An analytical model for the steady-state and transient characteristics of the power insulated-gate bipolar transistor." Solid-State Electronics 31, no. 10 (1988): 1513-1532. https://doi.org/10.1016/0038-1101(88)90025-1

Kraus, R., P. Turkes, and J. Sigg. "Physics-based models of power semiconductor devices for the circuit simulator SPICE." In PESC 98 Record. 29th Annual IEEE Power Electronics Specialists Conference (Cat. No. 98CH36196), vol. 2, pp. 1726-1731. IEEE, 1998.

Tichenor, Jerry L., Scott D. Sudhoff, and James L. Drewniak. "Behavioral IGBT modeling for predicting high frequency effects in motor drives." IEEE Transactions on Power Electronics 15, no. 2 (2000): 354-360. https://doi.org/10.1109/63.838108

Oh, Hyeong-Seok, and Mahmoud El Nokali. "A new IGBT behavioral model." Solid-State Electronics 45, no. 12 (2001): 2069-2075. https://doi.org/10.1016/S0038-1101(01)00149-6

Azar, R., F. Udrea, M. De Silva, G. Amaratunga, W. T. Ng, F. Dawson, W. Findlay, and P. Waind. "Advanced SPICE modeling of large power IGBT modules." In Conference Record of the 2002 IEEE Industry Applications Conference. 37th IAS Annual Meeting (Cat. No. 02CH37344), vol. 4, pp. 2433-2436. IEEE, 2002.

Asparuhova, Katya, and Tsvetana Grigorova. "IGBT high accuracy behavioral macromodel." In 2008 26th International Conference on Microelectronics, pp. 185-188. IEEE, 2008. https://doi.org/10.1109/ICMEL.2008.4559254

Frisina, F., C. Leonardi, Angelo Raciti, and Salvatore Torrisi. "Physics based model of punch through IGBTs simulated by PSpice." In COM. P. EL. 98. Record 6th Workshop on Computer in Power Electronics (Cat. No. 98TH8358), pp. 27-35. IEEE, 1998.

Driss, Améni, Samah Maalej, and Mohamed Chaker Zaghdoudi. "Experimentation and modeling of the steady-state and transient thermal performances of a helicoidally grooved cylindrical heat pipe." Microelectronics Reliability 62 (2016): 102-112. https://doi.org/10.1016/j.microrel.2016.03.022

Driss, A., M. B. H. Sassi, S. Maalej, and M. C. Zaghdoudi. "Transient thermal performance modeling and experimentation of heat pipes for high power electronics cooling." International Review on Modeling and Simulations (IREMOS) 5, no. 6 (2012): 2473-2483.

Semitrans. "Semitrans IGBT module (SKM75GB123D)." (2009).

Gerstenmaier, York C., Walter Kiffe, and Gerhard Wachutka. "Combination of thermal subsystems modeled by rapid circuit transformation." In 2007 13th International Workshop on Thermal Investigation of ICs and Systems (THERMINIC), pp. 115-120. IEEE, 2007. https://doi.org/10.1109/THERMINIC.2007.4451758

Gerstenmaier, Y. C., W. Kiffe, and G. Wachutka. "Combination of thermal subsystems by use of rapid circuit transformation and extended two-port theory." Microelectronics Journal 40, no. 1 (2009): 26-34. https://doi.org/10.1016/j.mejo.2008.09.002

Ayadi, M., M. A. Fakhfakh, M. Ghariani, and R. Neji. "Electro-thermal simulation of a three phase inverter with cooling system." Journal of Modelling and Simulation of Systems 1, no. 3 (2010): 163-170.

Downloads

Published

2021-08-14

How to Cite

Driss, A., Maalej, S., & Zaghdoudi, M. C. . (2021). Electro-Thermal Modeling of Power IGBT Module Cooled by A Heat Pipe Cooling System. Journal of Advanced Research in Fluid Mechanics and Thermal Sciences, 86(1), 105–122. https://doi.org/10.37934/arfmts.86.1.105122

Issue

Section

Articles